ProControl2 Remote Readout System-Developed to Use for Industrial Petroleum Sectors

ProControl2 Remote Readout system is a new innovative wireless industrial device that is designed with RFID system. These systems are built to take your existing wireless system into the next level. It is considered as an all-in-one wireless remote controller that is built to improve your industrial petroleum delivery efficiency. At the same time it is also used to reduce costly refueling mistakes.

One of the great advantages of these wireless remote controllers is that it can be easily retrofitted with your existing trucks. One can install these systems in newly developed equipment as well. As these systems are is ATEX certified for using in the hazardous locations throughout the world.

Apart from that there are other aspects of these RFID equipped Remote Readout Systems:

1. The chief aim of designing these Readout systems is to allow the complete control over the fuel delivery operations in industrial petroleum operations.

2. RFID equipped Remote Readout device has also a handheld remote control unit including a backlit LCD display and that can operate up to 500ft from truck.

3. The hose reel industrial remote control devices can allow the operator to rewind or unwind delivery hose savings hose wear.

4. The meter register system of these wireless devices is equipped with a Direct Serial Interface that can show the mirror image volume that is identical to the truck mounted register.

5. You can also control the Engine RPM with handheld wireless remote controllers in order to increase or decrease pump volume.

The handheld controllers are used to ensure interference free control. They are equipped with Frequency hopping spread spectrum technology that shuts down the whole system during any little signal loss or disturbance. The transmitter of the Receiver has a frequency operation of 2.4 Hz DSS, optional 869.7 and 902-928 MHz is also available.

Tank Truck Equipment- Essential for Industrial Area

Tank truck equipment is a motor vehicle specially designed to carry liquefied loads, dry bulk cargo or gases on roads. Basically the largest such vehicles are similar to railroad tank cars which are also designed to carry liquefied loads. Most of the alternatives exist due to the wide to the variety of liquids that can be transported. Basically these tank truck equipments tend to be large; they may be insulated or non-insulated, pressurized or non- pressurized. At the same time it is designed for single or multiple loads. Some are semi trailer trucks. They are difficult to drive; due to their center of gravity.

During these days, tank loading equipments are really popular in industrial area. These are used to transport gasoline to filling stations. At the same time they also transport a wide variety for liquid goods such as concrete, oil, gasoline diesel and other chemical. Tank trucks are constructed with various materials depending on what products they are transporting. These materials include Aluminum, carbon steel, stainless steel and Fiberglass etc. Actually these truck loading equipments are really helpful for industrial area. It is really not possible for us to move a huge machine one place to another place. This is the reason now most of the reputed company uses tank truck equipment for the business.

However some trucks are able to carry multiple products at once. This allows for an increased number of delivery options. These trucks are commonly used to carry different grades of gasoline to service stations to carry all products needed in one trip.

Tank Truck Equipment For Industrial Area

A true fact is to begin our new life when we pack up our possessions and venture to another place; we always use a moving truck. There is no doubt this is one of the best medium to carry our heavy utensils to one place to another. Truck loading equipment is one of an efficient medium of carrying utensils one place to another. There are many important ways to properly and efficiently load a moving truck.

If you critically analyze you can notice truck loading equipment is mostly used in industrial area. Basically this is not possible for you to engage hundred people for a particular job. It is costly and time taking. This is the reason now most of the reputed company uses tank truck equipment. These are really cheap and affordable.


However before loading the industrial product you have to follow some significant guidelines which are really important. And if you don’t maintain these all may be it could be risky while the vehicle moves to its destination. Apart form, you have to follow some laws you must follow which concerning moving trucks that need to be followed in order to avoid being fined.

On thing is most important, before moving the vehicle you should aware with the weight product capacity. Do one thing, please note of the weight of the items that you will transport. There is no doubt each and every vehicle has a capacity. Definitely should stay within the limits’. Never push the vehicle above the limit. Another thing is if something is wrong with the vehicle, have it fixed properly and immediately to ensure safety not only the things that are going to be transported but also for your own safety.

A General View about Automatic Truck Loading System

Truck loading and unloading is such a need that all kinds of people are familiar with. It is really necessary while shifting from one place to another place. Apart from the domestic uses, truck loading is a kind of job that is abundantly happened in the industrial fields. Probably industrial fields require it most. Generally manual labor is used to load or unload trucks in small businesses where the quantity of products is very small. But most of the large engineering companies use wireless truck loading system. These wireless equipments are being used by the engineering companies in a wide range.

The job of loading or unloading trucks needs a great effort when it is done by applying manual effort. Manual process also is quite risky as there is always a chance of some accident. It is quite safe for your valuable products also. Any automation is always considered safe and it always needs less effort. It also saves your valuable time. That is the reason why most of the heavy-engineering companies, today, are using automatic loading equipments.

There is no doubt that in today’s logistics and manufacturing environment automation plays an important role. But there are some issues also that we should always keep in mind while implementing these equipments for our own use. The first thing is that it is quite expensive to use in a long time need. As these equipments are quite heavy it is very difficult to move them with single effort.

Another chief aspect about this equipment is that they are made with complex mechanical and software devices. If any modification is needed we have to call a certified engineer only. If you are not a professional of this field or if you are not directly related with this equipment, you are advised not to apply your own effort to modify it. It could be harmful for you and your machine also. When a significant part of these systems fails, the whole system usually goes down.

In spite of these problems, using wireless truck loading equipment is always useful as they have some advantages. First of all, these products really provide high capacity of service. They can serve you a large amount of your job within a few minutes. Most of the wireless loading devices are made with high loading speed. Another advantage of these products is that they are very compact and they are easy to integrate with any of your existing operation. While using they improve the shipping accuracy. They will surely reduce labor cost and product damage.

They are safe to use as they reduces fork lift related accidents. They are also very flexible. They can handle any type of pallet, slip sheet, skid, rack or other unitized products. They can even work with non modified trucks, trailers and containers. Most of these automated devices can perform both loading and unloading service. They can even work with straight or zigzag doors.

These devices can be run by using normal plant power but you can also use batteries to run them. Nowadays, most of companies offer radio truck loading systems with proper warranty. They also provide other necessary equipments like hand held joysticks, charger, leather case etc.

How a Wireless Winch Control Works

A wireless winch control is a device that is connected with the front or back side of a heavy vehicle and it is used to lift or pull heavy vehicles. There is basic difference between a traditional winch and a wireless winch. The older winches are generally controlled manually. But the wireless winches are controlled by an automatic control unit. The typical winches are connected with a handheld controller. It is controlled by a cable or wire. Wireless winch devices can be controlled without any cable or wire.

These winches can transmit wireless control signals. Generally the winches are controlled by radio frequency system but the other communication methods are also applied. Depending on the use the size and function of a radio winch varies. But the process in which the items are hauled is quite similar. Though there might be some variation in some winches.

More or less all the radio winches work through same methods. A long cable is wrapped around a pulley by number of times. The pulley is attached with a motor that generally turns the wheel in any directions. This movement depends on the user’s choice on which direction they want to move the cable. At first when the users first activate the motor to turn the pulley in a particular direction, the cable is fed out and it turns into a solid or heavy object. After that the pulley turns into the other direction and the cable is retracted. By doing this the cable will become able to move any heavy object or to pull the vehicle to which the wireless winch is attached.

In the traditional winch system the users had to stand beside the system and they had to plug in a hand controller that was used to activate the pulley. No doubt, the process was more complex and hard. But the modern system doesn’t need to plug in any hand controller. During the progress the users can move with vehicle and they can supervise the vehicle or the products that are being moved.

These wireless systems are also very safe to use. As the user can move freely during its function they can protect themselves from getting caught in the moving pulley. The chance of getting injured by the vehicle is also very low. In some modern winches the users can also operate the whole system by sitting inside the vehicle. They are also able to drive the vehicle during the operation. Its uniqueness in appearance and its user friendliness makes the system more popular among the engineering companies.

Those who want to adopt a radio winch for their use can contact with the manufacturers. They can also go through the manufacturers’ website just by using their computer. These websites are very useful to get information about a particular wireless winch product. There one can find images of different products along with their price and short description. Although the price of the modern winch system is little high but the price can be considered as they are quite effective and useful rather than the old weird systems.

Process Control uses for Excessive Production

Nowadays in the era of digital buses, one can plug in a laptop or use a wireless hand tool and instantly access all your important data. No doubt this all happen with the help of modern technology. Now the technical advancement in procedure monitoring, control and industrial automation over the past decades have contributed seriously to improve the productivity of virtually all manufacturing company all over the world. Process control is a statistics that deals with machine, architecture, and algorithms. Basically this is need for maintaining the output of a specific process with in a desire level. Nowadays process control is excessively uses in industry for more production, Not only that the continuing process like oil refining, paper manufacturing chemicals power plants and other industries. Process controls are enabling for automation.

Apart from that Industrial petroleum is very essential for gigantean machines. Naturally oil is naturally occurring flammable, liquid consisting of complex mixture of hydrochlorides of various molecular weights and other liquid organic compounds. No doubt it is refined and separated and finally uses in machines. Basically industrial petroleum keeps huge industrial machines smooth and productive. That’s why most of the reputed company uses it.

Features and benefits of Hydraulic Remote Control

Wise people say, necessity is the mother of invention. We have got the proof repeatedly during the course of our life. We are inventing different technology for own needs. It can be effortlessly said that all these are possible with the help of modern technology. Today we are habituated with these technologies. Without these we can’t think our life for a moment.

During these days we are living in informative world, where we can contact with a person very easily within a few seconds. This is also the blessings of the modern technology. Nowadays we are using different wireless system. And it is possible for this high profile technology and the communication system has also upgraded. And through the strong communication system now one can easily provide essential documents to any source. It is possible over a short or long distance.

Needless to say, the affluence of the modern industry has been doing a great favors to our everyday life as well as in industrial system. Generally there comes a great variety of the remote control to meet the increasing requirements. Among of the various type of remote controls the hydraulic remote control playing a wonderful responsibility in industrial system. As well as some reputed company uses wireless remote control, remote winch controls etc. Here are some unique aspects about the Hydraulic remote controls.

Hydraulic remote control:

These machines are superior precision, quality and enhanced safety equipment for industrial system. With the help of this apparatus one can maintain the huge machines for different purpose.
Basically these machines are used to activate and control the directional valves from a remote and signal operating system. Generally the hydraulic remote controls are come in hand, foot and mechanically worked version. Not only that these are typically installed on vehicles in seats armrests or in a console.

Operation: 

Essential information is that the 50 design hydraulic remote control system operates on input flows up to 20L/min and the pressure up to 100 bars. Apart from that, from the input a HRC can create reduced output pressures. And by applying the pressure s to main directional control valves speed and direction of hydraulic actuators can be precisely metered.

There are so many benefits and features of a hydraulic remote control. These are:
It’s high productivity:

This machine requires very little operating effort. That’s why you get more from both man and machine.

It’s precise Control:

No doubt its excellent pressure meeting capacity allows precise control of work functions and less wear and tear on the application.

The freedom of system:

The signal stations control placed directional valves is readily achieved. As an example, in a vehicle a HRC is easily mountable in the cab, because this is compact and eliminates the cumbersome mechanical linkage founds in many applications.

A safer, cleaner operating environment:

The designing an ergonomic workstation is easily achieved by leveraging benefits inherent in a system designed with hydraulic remote control.

It’s a wide range of output pressure characteristics:

This is can be perfectly matched to the main stage valve.

Less Noise: 

No doubt, the use of a HRC allows better insulation between the cab and engine because there is no longer a need of holes through the cab wall for linkages to the main valve. So it produces less noise.